Chair of Turbomachinery and Flight Propulsion

2024

AN AERO ENGINE DISK SIZING AND WEIGHT ESTIMATION APPROACH WITH IMPROVED TEMPERATURE PROFILES

Zaimis, I., Carpentari, E., Begiebing, T. & Gümmer, V., 2024, Aircraft Engine. American Society of Mechanical Engineers (ASME), V001T01A038. (Proceedings of the ASME Turbo Expo; vol. 1).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

GASEOUS AND PARTICULATE EMISSIONS OF AN ALLISON 250-C20B TURBOSHAFT ENGINE RUNNING ON HEFA-SPK AND ITS JET A-1 BLENDS

Rabl, A., Rohkamp, M., Saraji-Bozorgzad, M. R., Helcig, C., Sallinen, R., Vilja, J., Bendl, J., Adam, T., Hupfer, A. & Gümmer, V., 2024, Ceramics and Ceramic Composites; Coal, Biomass, Hydrogen, and Alternative Fuels. American Society of Mechanical Engineers (ASME), V002T03A022. (Proceedings of the ASME Turbo Expo; vol. 2).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

NUMERICAL ANALYSIS OF THE BOUNDARY LAYER BEHAVIOR OF LOW-SPEED LINEAR CASCADE COMPRESSOR AIRFOILS WITH SINGLE AND TANDEM CONFIGURATIONS

Reisinger, L., Bieli, P. & Gümmer, V., 2024, Turbomachinery - Axial Flow Fan and Compressor Aerodynamics. American Society of Mechanical Engineers (ASME), v12at29a048. (Proceedings of the ASME Turbo Expo; vol. 12A).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

NUMERICAL INVESTIGATION OF THE EFFECT OF DIFFUSION FACTOR VARIATION ON THE PERFORMANCE OF SINGLE-ROW AND TANDEM BLADINGS IN LOW-SPEED AXIAL COMPRESSOR STAGES

von Jeinsen, P., Giannini, S. & Gümmer, V., 2024, Turbomachinery - Axial Flow Fan and Compressor Aerodynamics. American Society of Mechanical Engineers (ASME), v12at29a037. (Proceedings of the ASME Turbo Expo; vol. 12A).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

NUMERICAL INVESTIGATION OF WINDAGE HEATING IN HIGH-PRESSURE COMPRESSOR SHROUDED STATOR CAVITIES

Damgacioglu, A., Cottier, F. & Gümmer, V., 2024, Heat Transfer: Internal Air Systems; Heat Transfer: Internal Cooling; Industrial and Cogeneration. American Society of Mechanical Engineers (ASME), V008T14A008. (Proceedings of the ASME Turbo Expo; vol. 8).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

OPTIMIZATION OF A BATTERY ELECTRIC HYBRID PROPULSION SYSTEM FOR A SHORT RANGE AIRCRAFT

Schroeter, J., Armbrüster, F., Schaber, R. & Gümmer, V., 2024, Aircraft Engine. American Society of Mechanical Engineers (ASME), V001T01A037. (Proceedings of the ASME Turbo Expo; vol. 1).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

THE UNSTEADY SHOCK-BOUNDARY LAYER INTERACTION IN A COMPRESSOR CASCADE – PART 3: MECHANISMS OF SHOCK OSCILLATION

Munoz Lopez, E. J., Hergt, A., Klinner, J., Klose, B., Willert, C. & Gümmer, V., 2024, Turbomachinery - Multidisciplinary Design Approaches, Optimization, and Uncertainty Quantification; Radial Turbomachinery Aerodynamics; Unsteady Flows in Turbomachinery. American Society of Mechanical Engineers (ASME), V12DT36A019. (Proceedings of the ASME Turbo Expo; vol. 12D).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

Open Access

2023

A NUMERICAL DESIGN SPACE INVESTIGATION OF LOW-SPEED AXIAL COMPRESSOR STAGES USING SINGLE-ROW AND TANDEM BLADINGS

von Jeinsen, P., Eckel, J., Giannini, S. & Gümmer, V., 2023, Turbomachinery - Axial Flow Fan and Compressor Aerodynamics. American Society of Mechanical Engineers (ASME), v13at29a019. (Proceedings of the ASME Turbo Expo; vol. 13A).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

2 Scopus citations

ATTENUATION OF DETRIMENTAL HUB LEAKAGE EFFECTS IN AN AXIAL COMPRESSOR ROTOR BY CUSTOMIZED GEOMETRICAL DESIGN FEATURES

Petermann, J., Schulz, K., Gümmer, V. & Becker, B., 2023, Turbomachinery - Axial Flow Fan and Compressor Aerodynamics. American Society of Mechanical Engineers (ASME), v13at29a003. (Proceedings of the ASME Turbo Expo; vol. 13A).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

CHALLENGES IN THE APPLICATION OF HOT-WIRE ANEMOMETRY FOR THE INVESTIGATION OF TRANSIENT TEMPERATURE FLUCTUATIONS IN A HIGH-SPEED RESEARCH COMPRESSOR

Schäffer, C., Rabl, A., Speck, K., Boetzel, K., Helcig, C. & Gümmer, V., 2023, Controls, Diagnostics, and Instrumentation. American Society of Mechanical Engineers (ASME), v004t05a003. (Proceedings of the ASME Turbo Expo; vol. 4).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

DETAILED GASEOUS AND PARTICULATE EMISSIONS OF AN ALLISON 250-C20B TURBOSHAFT ENGINE

Rohkamp, M., Rabl, A., Gündling, B., Saraji-Bozorgzad, M. R., Mull, C., Bendl, J., Neukirchen, C., Helcig, C., Adam, T., Gümmer, V. & Hupfer, A., 2023, Combustion, Fuels, and Emissions. American Society of Mechanical Engineers (ASME), v03at04a019. (Proceedings of the ASME Turbo Expo; vol. 3A-2023).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

1 Scopus citations

INVESTIGATION OF THE EFFECT OF BLADE PASSING ON TWO-PHASE FLOW WITHIN DISCRETE COMPRESSOR CASING RECIRCULATION CHANNEL USING PARTICLE IMAGE VELOCIMETRY

Mendoza, C. E., Bedii Ozdemir, I., Helcig, C. & Gümmer, V., 2023, Turbomachinery - Axial Flow Fan and Compressor Aerodynamics. American Society of Mechanical Engineers (ASME), v13at29a025. (Proceedings of the ASME Turbo Expo; vol. 13A).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

INVESTIGATIONS OF THE UNSTEADY SHOCK-BOUNDARY LAYER INTERACTION IN A TRANSONIC COMPRESSOR CASCADE

Munoz Lopez, E. J., Hergt, A., Klinner, J., Grund, S., Karboujian, J., Flamm, J. & Gümmer, V., 2023, Turbomachinery - Multidisciplinary Design Approaches, Optimization, and Uncertainty Quantification; Radial Turbomachinery Aerodynamics; Unsteady Flows in Turbomachinery. American Society of Mechanical Engineers (ASME), v13dt36a015. (Proceedings of the ASME Turbo Expo; vol. 13D).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

2 Scopus citations

MULTIDISCIPLINARY ASSESSMENT OF FOREIGN OBJECT DAMAGE (FOD) SENSITIVE REGIONS ON A COMPRESSOR ROTOR BLADE

Rocchi, S., Roth, C., Froebel, T., Hackenberg, H. P. & Gümmer, V., 2023, Turbomachinery - Axial Flow Fan and Compressor Aerodynamics. American Society of Mechanical Engineers (ASME), v13at29a026. (Proceedings of the ASME Turbo Expo; vol. 13A).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

NUMERICAL INVESTIGATION OF THE INFLUENCE OF THE DEGREE OF REACTION IN AN AXIAL COMPRESSOR STAGE WITH TANDEM VANES

Giannini, S., Luz, G. M., von Jeinsen, P., Straccia, M. & Gümmer, V., 2023, Turbomachinery - Axial Flow Fan and Compressor Aerodynamics. American Society of Mechanical Engineers (ASME), v13at29a004. (Proceedings of the ASME Turbo Expo; vol. 13A).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

NUMERICAL INVESTIGATION OF THE INTERACTION OF A CIRCUMFERENTIAL GROOVE CASING TREATMENT AND NEAR-TIP MODIFICATIONS FOR A HIGHLY-LOADED LOW-SPEED ROTOR UNDER THE INFLUENCE OF DOUBLE LEAKAGE

Reisinger, L., Eckel, J., von Jeinsen, P. & Gümmer, V., 2023, Turbomachinery - Axial Flow Fan and Compressor Aerodynamics. American Society of Mechanical Engineers (ASME), v13at29a010. (Proceedings of the ASME Turbo Expo; vol. 13A).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

PARAMETRIC CYCLE STUDIES OF THE WATER-ENHANCED TURBOFAN CONCEPT

Ziegler, P., Kaiser, S. & Gümmer, V., 2023, Cycle Innovations. American Society of Mechanical Engineers (ASME), v005t06a001. (Proceedings of the ASME Turbo Expo; vol. 5).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

4 Scopus citations

2022

ANALYSIS OF CAVITY LEAKAGE EFFECTS ON COUPLED NON-AXISYMMETRIC ENDWALL-AIRFOIL OPTIMIZATION IN A LOW-SPEED COMPRESSOR TANDEM STATOR

Straccia, M., Giannini, S. & Gümmer, V., 2022, Turbomachinery - Design Methods and CFD Modeling for Turbomachinery; Ducts, Noise, and Component Interactions. American Society of Mechanical Engineers (ASME), V10CT32A027. (Proceedings of the ASME Turbo Expo; vol. 10-C).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

5 Scopus citations

An Auxetic Construction Kit for Turbomachinery Application

Schröter, S., Reisinger, L. & Gümmer, V., 2022, Proceedings of the 8th World Congress on Mechanical, Chemical, and Material Engineering, MCM 2022. Qiu, H., Zhang, Y. & Iasiello, M. (eds.). Avestia Publishing, (Proceedings of the World Congress on Mechanical, Chemical, and Material Engineering).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

Open Access

DESIGN OF A BLOWING TYPE FLOW TREATMENT TO COMPLEMENT CASING TREATMENTS FOR COMPACT HIGH-PRESSURE COMPRESSOR REAR STAGES

Köhler, C. P., Kendall-Torry, C., Helcig, C. & Gümmer, V., 2022, Turbomachinery - Axial Flow Fan and Compressor Aerodynamics. American Society of Mechanical Engineers (ASME), V10AT29A002. (Proceedings of the ASME Turbo Expo; vol. 10-A).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

Open Access

1 Scopus citations

HARDWARE-IN-THE-LOOP EVALUATION OF A QUICK-START SYSTEM FOR HELICOPTER GAS TURBINE OEI OPERATIONS TESTED IN SIMULATED FLIGHTS

Kuen, N., Mehling, T., Reiser, A., Bludau, J., Hajek, M. & Gümmer, V., 2022, 48rd European Rotorcraft Forum, ERF 2022. Associazione Italiana di Aeronautica e Astronautica (AIDAA), (48rd European Rotorcraft Forum, ERF 2022).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

NUMERICAL ANALYSIS OF BLADE PLATFORM LEAKAGE IN AXIAL COMPRESSORS

Petermann, J., Pommerening, M., Gümmer, V. & Becker, B., 2022, Turbomachinery - Axial Flow Fan and Compressor Aerodynamics. American Society of Mechanical Engineers (ASME), V10AT29A004. (Proceedings of the ASME Turbo Expo; vol. 10-A).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

2 Scopus citations

NUMERICAL INVESTIGATION OF NEAR-TIP MODIFICATIONS FOR A HIGHLY-LOADED LOW-SPEED ROTOR UNDER THE INFLUENCE OF DOUBLE LEAKAGE

Eckel, J., von Jeinsen, P. & Gümmer, V., 2022, Turbomachinery - Axial Flow Fan and Compressor Aerodynamics. American Society of Mechanical Engineers (ASME), V10AT29A023. (Proceedings of the ASME Turbo Expo; vol. 10-A).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

2021

Coupling of endwall and aerofoil optimisation on a low-speed compressor tandem stator

Straccia, M. & Gummer, V., 2021, Turbomachinery - Multidisciplinary Design Approaches, Optimization, and Uncertainty Quantification; Radial Turbomachinery Aerodynamics; Unsteady Flows in Turbomachinery. American Society of Mechanical Engineers (ASME), V02DT36A009. (Proceedings of the ASME Turbo Expo; vol. 2D-2021).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

4 Scopus citations

ENDWALL BOUNDARY LAYER DEVELOPMENT in A MULTISTAGE LOW-SPEED COMPRESSOR with TANDEM STATOR VANES

Hopfinger, M. & Gümmer, V., 2021, Turbomachinery - Axial Flow Fan and Compressor Aerodynamics. American Society of Mechanical Engineers (ASME), V02AT31A014. (Proceedings of the ASME Turbo Expo; vol. 2A-2021).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

Numerical calibration and investigation of the influence of reynolds number on measurements with five-hole probes in compressible flows

Schaffer, C., Speck, K. & Gummer, V., 2021, Controls, Diagnostics, and Instrumentation; Cycle Innovations; Cycle Innovations: Energy Storage; Education; Electric Power. American Society of Mechanical Engineers (ASME), V004T05A002. (Proceedings of the ASME Turbo Expo; vol. 4).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

Open Access

3 Scopus citations

NUMERICAL EVALUATION of LOSSES in SHROUDED and CANTILEVERED STATORS of A MULTI-STAGE AXIAL COMPRESSOR

Dominicis, I. D., Robens, S. & Gümmer1, V., 2021, Turbomachinery - Axial Flow Fan and Compressor Aerodynamics. American Society of Mechanical Engineers (ASME), V02AT31A003. (Proceedings of the ASME Turbo Expo; vol. 2A-2021).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

NUMERICAL INVESTIGATION of the AERODYNAMIC PERFORMANCE of HYBRID AEROFOILS in A 1.5-STAGE LOW-SPEED COMPRESSOR

Eckel, J. & Gümmer, V., 2021, Turbomachinery - Axial Flow Fan and Compressor Aerodynamics. American Society of Mechanical Engineers (ASME), V02AT31A008. (Proceedings of the ASME Turbo Expo; vol. 2A-2021).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

8 Scopus citations

2020

Experimental investigation of the starting procedure of a helicopter gas turbine featuring an impingement quick-start system

Kuen, N. & Gümmer, V., 2020, Controls, Diagnostics, and Instrumentation; Cycle Innovations; Cycle Innovations: Energy Storage. American Society of Mechanical Engineers (ASME), (Proceedings of the ASME Turbo Expo; vol. 5).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

1 Scopus citations

Reduced-order modelling of rotating stall

Schlüter, D., Grewe, R. P., Wartzek, F., Liefke, A., Werner, J., Kunkel, C. & Gümmer, V., 2020, Turbomachinery. American Society of Mechanical Engineers (ASME), (Proceedings of the ASME Turbo Expo; vol. 2E-2020).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

1 Scopus citations

2019

Development and commissioning of a high-speed research compressor facility

Schmieder, M., Erhard, W., Gümmer, V., Aalburg, C., Schuler, P., Schneider, C. M., Pannekeet, R. C. & Vallikivi, M., 2019, AIAA Propulsion and Energy Forum and Exposition, 2019. American Institute of Aeronautics and Astronautics Inc, AIAA, (AIAA Propulsion and Energy Forum and Exposition, 2019).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

2 Scopus citations

Interacting flow effects in the stages of a low-speed multistage axial compressor using shrouded and cantilevered stators

De Dominicis, I., Robens, S., Wolfrum, N., Lange, M. & Gümmer, V., 2019, AIAA Propulsion and Energy Forum and Exposition, 2019. American Institute of Aeronautics and Astronautics Inc, AIAA, (AIAA Propulsion and Energy Forum and Exposition, 2019).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

4 Scopus citations

New methods for secondary flow phenomena visualization and analysis

Straccia, M., Hofmann, R. & Gümmer, V., 2019, Turbomachinery. American Society of Mechanical Engineers (ASME), (Proceedings of the ASME Turbo Expo; vol. 2C-2019).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

6 Scopus citations

Optimization design analysis of primary surface recuperator for rotorcraft powerplant applications

Zhang, C. & Gümmer, V., 2019, Heat Transfer. American Society of Mechanical Engineers (ASME), (Proceedings of the ASME Turbo Expo; vol. 5B-2019).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

1 Scopus citations

Preliminary design of a three-stage low-speed research compressor using tandem vanes

Hopfinger, M. & Gümmer, V., 2019, AIAA Propulsion and Energy Forum and Exposition, 2019. American Institute of Aeronautics and Astronautics Inc, AIAA, (AIAA Propulsion and Energy Forum and Exposition, 2019).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

15 Scopus citations

Reducing compressor shroud leakage flows by raising the Stator hub line: Low speed tests

Schrapp, H., Dodegge, A., Gümmer, V., Harvey, N. W., Städing, J. & Friedrichs, J., 2019, Turbomachinery. American Society of Mechanical Engineers (ASME), (Proceedings of the ASME Turbo Expo; vol. 2A-2019).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

3 Scopus citations

Structural analysis of an auxetic casing structure incorporating tip blowing casing treatment modification

Schmidt, T., Lorenz, J., Gümmer, V. & Hupfer, A., 2019, Structures and Dynamics. American Society of Mechanical Engineers (ASME), (Proceedings of the ASME Turbo Expo; vol. 7A-2019).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

2018

Evaluation of the fuel saving potential regarding recuperated helicopter flight conditions

Zhang, C., Kerler, M. & Gümmer, V., 2018, Aircraft Engine; Fans and Blowers; Marine. American Society of Mechanical Engineers (ASME), (Proceedings of the ASME Turbo Expo; vol. 1).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

6 Scopus citations

Experimental investigation of a radial turboshaft engine intake

Fuchs, F., Schäffer, C. & Gümmer, V., 2018, 2018 Joint Propulsion Conference. American Institute of Aeronautics and Astronautics Inc, AIAA, AIAA 2018-4747. (2018 Joint Propulsion Conference).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

1 Scopus citations

2016

Design of an airworthy turboshaft engine quick-start system with compact pressurized air supply for rotorcraft application

Kerler, M., Scháffer, C., Erhard, W. & Gümmer, V., 2016, 42nd European Rotorcraft Forum 2016. Association Aeronautique et Astronautique de France, p. 1459-1465 7 p. (42nd European Rotorcraft Forum 2016; vol. 2).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

1 Scopus citations

Design parameter identification of the air supply for a turboshaft engine quick-start system

Kerler, M., Schäffer, C., Erhard, W. & Gümmer, V., 2016, 52nd AIAA/SAE/ASEE Joint Propulsion Conference, 2016. American Institute of Aeronautics and Astronautics Inc, AIAA, (52nd AIAA/SAE/ASEE Joint Propulsion Conference, 2016).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

4 Scopus citations

Fatigue analysis of a cylindrical turbine disk with integrated heat pipes

Eisenmann, S., Schmidt, T., Gümmer, V. & Hupfer, A., 2016, 52nd AIAA/SAE/ASEE Joint Propulsion Conference, 2016. American Institute of Aeronautics and Astronautics Inc, AIAA, (52nd AIAA/SAE/ASEE Joint Propulsion Conference, 2016).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

3 Scopus citations

2014

Tip gap variation on a transonic rotor in the presence of tip blowing

Guinet, C., Streit, J. A., Kau, H. P. & Gümmer, V., 2014, Turbomachinery. American Society of Mechanical Engineers (ASME), (Proceedings of the ASME Turbo Expo; vol. 2A).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

15 Scopus citations

2013

Aerodynamic design of abradable liners with integrated endwall treatments for axial compressor rotors

Mayenberger, T., Kau, H. P. & Brignole, G., 2013, ASME Turbo Expo 2013: Turbine Technical Conference and Exposition, GT 2013. (Proceedings of the ASME Turbo Expo; vol. 6 A).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

1 Scopus citations

Aerodynamic origin of rotor-rotor interaction noise from unducted propulsors

Danner, F., Kendall-Torry, C. & Kau, H. P., 2013, ASME Turbo Expo 2013: Turbine Technical Conference and Exposition, GT 2013. GT2013-95572. (Proceedings of the ASME Turbo Expo; vol. 6 C).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

7 Scopus citations

An evaluation of the potential of additive manufacturing technologies in future aero engine design

Rockel, D., Hupfer, A. & Kau, H. P., 2013, 49th AIAA/ASME/SAE/ASEE Joint PropulsionConference. (49th AIAA/ASME/SAE/ASEE Joint Propulsion Conference).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

5 Scopus citations

An evaluation of the potential of additive manufacturing technologies in future aero engine design

Rockel, D., Hupfer, A. & Kau, H. P., 2013, 49th AIAA/ASME/SAE/ASEE Joint Propulsion Conference. American Institute of Aeronautics and Astronautics Inc., (49th AIAA/ASME/SAE/ASEE Joint Propulsion Conference; vol. 1 PartF).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

Axial-slot casing treatments improve the efficiency of axial flow compressors: Aerodynamic effects of a rotor redesign

Streit, J. A., Heinichen, F. & Kau, H. P., 2013, ASME Turbo Expo 2013: Turbine Technical Conference and Exposition, GT 2013. (Proceedings of the ASME Turbo Expo; vol. 6 A).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

15 Scopus citations

Design study on an additively manufactured compressor casing containing auxetic structures

Rockel, D., Hupfer, A. & Kau, H. P., 2013, SME Technical Papers - 4th Quarter 2013. Society of Manufacturing Engineers, (Technical Paper - Society of Manufacturing Engineers; vol. TP13PUB81).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

4 Scopus citations

Evolution of generic vanelets applied to a high pressure compressor

Loos, A., Mayenberger, T., Danner, F. & Kau, H. P., 2013, ASME Turbo Expo 2013: Turbine Technical Conference and Exposition, GT 2013. (Proceedings of the ASME Turbo Expo; vol. 6 A).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

Chair of Turbomachinery and Flight Propulsion

Research output

Search results